佛山市通能建筑材料有限公司官方网站!
  • 咨询热线:18676546655
  • 佛山市通能建筑材料有限公司
    网站首页 关于我们 产品中心 应用案例 新闻中心 常见问题 联系我们
    请在后台添加网站优化关键词!
     
    安装事项

    Qualification certificate

     
    

    安装方法

      (一) 嵌入式安装法 a 保护膜会影响填缝料与中空板的结合,故在嵌入安装前,要求先去掉嵌入量为5-10cm宽的保护膜。 b 板材热胀冷缩系数与支撑框架不同,且需要留余量以承受风压、雪压等,因此嵌入量要预留充分,以及热胀冷缩的空间。一般板材边缘伸入固定框架25mm以上,并至少有二条筋肋安装进固定区域;热胀冷缩一般每米留3mm空隙。(热膨胀率为0.065mm/moC

     

       (二)螺丝安装法 a 螺栓或铆钉穿孔安装时,板材的开孔孔径须比螺栓或铆灯直径大50%,以防热胀冷缩。 b 所有孔穴均应以硅酮密封胶填满空隙及覆盖外露部分,防止水分或清洁济进入。 c 铆钉头部应比柄部大2倍,并加上垫片或华司,避免在局部产生大压强损坏板材。 d 螺丝不宜拧得太紧,避免压裂板材。 e 不宜使用PV垫片或含沥青成份的防水胶布。 f 冷弯加工时,弯曲部分避免使用螺丝固定

     

     

    通能塑胶PC结构板系列使用须知

    1.通能PC结构板的储运:

    运输过程中避免将重物置于PC板上,也不可将锐器接触板材:卷材装卸需用机械,或利用车辆跳板小心轻卸。另外,PC板不可暴露在室外进行存放,应置于阴凉处。

    2.通能PC结构板的裁切:

    阳光板可以利用锋利的墙纸切开:耐力板可用手锯进行切割,介切割时应将板材固定,避免剧烈振动引起板材撕裂。

    3.通能PC结构板的安装:

    安装时必须将PC板有防紫外标识的一面朝外。

    在安装前应将阳光板所有的空端用铝质封口带封住。

    在安装过程中,施工人员不可直接站在PC板上施工。

     施工完毕,应将PC板上的杂物清理干净。

    4. 通能PC结构板的清洗和维护:

    按照正确的方法和合适的工具定期清洗能延长PC板的使用寿命。

    a.小面积清洗:

        用温清水冲洗;

        用中性肥皂或家用洗涤剂兑温水进行冲洗,并用柔软的织物或海绵去除灰尘和污垢;

        用冷水冲洗并在干後用软布擦除水干後的斑点。

    b.大面积清洗:

       用水龙头或高压水枪冲洗;

    水中附加物应与PC板相容。

    c.清洗注意事项:

        不要打磨或用强碱清洗PC板,不要用干硬布或硬刷子擦表面,以免产生拉毛现象。

        不准用丁基溶纤剂和异丙醇溶液来清洗防紫外线的PC板材。

    d.建议清洁用溶剂: 

        无水酒精,石油醚(BP65)、乙烷、康烷。以避免将品诚阳光板、耐力板与不相溶的化学物质接触。

    以上事项仅供使用者用通能PC板时参考,解释权归属本公司。本公司不承担任何因使用不当而引起板材损坏的责任。其他未明事项可至电本公司。  



    Installation

    1)Embedded installation method: A, The protective film will affect the combination of the stuffing material and the hollow panel, so before the embedded installation, requested to remove the protective film in embedded capacity of 5-10cm width. B, Due to different Coefficient of thermal expansion and cold contractility between PC Sheets and Support Frameworks, so need to take a enough space to withstand wind pressure, snow pressure and so on, have to reserve enough place of embedded ,also the space of thermal expansion and cold contractility. Generally, the edge of PC panels need to insert more than 25mm to the fixed framework, also two ribs at least installed into the fixed region. Commonly, there have to keep 3mm interspace per meter for thermal expansion and cold contractility. (Rate of thermal expansion:0.065mm/moC)



    2) Screws installation method: A, In the processiion with screws or rivets, the opened aperture of PC sheets must is 50% bigger than the diameter of bolts or rivets. B, All holes gap and exposed part should be filled with silicone sealant to prevent the inflow of water or detergent. C, The head of rivet must is two times bigger than the handle, also with pads or Washers to avoid the panels damaged by the large pressure from local part. D, The screws should not be twisted too tight to fracture the plates. E, PV pads and waterproof adhesive plaster including asphalt composition are not appropriate to useng of perforation installat. F, When in the cold processing, the winding part should not fix by screws .



     


     
    专业制造商
    It is a leading enterprise in the field of deform separation
    立即咨询
    热线:18676546655
    24小时咨询热线:
    18676546655
    首页 关于我们 产品展示 应用案例 新闻中心 常见问题 在线留言 联系我们 网站地图 xml地图
     
     
    总经理:袁小姐   手机:18676546655  地址:佛山市顺德区北滘镇上僚工业区2号    座机:0757-23602789      传真:0757-23602783      邮箱:1967464723@qq.com
    佛山市通能建筑材料有限公司 版权所有     备案号:粤ICP备12003945号-2  
    在线客服